Lakeshore Learning Materials 642 Manuel d'utilisateur Page 21
- Page / 122
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Lake Shore Model 642 Electromagnet Power Supply User’s Manual
Magnet System Design 2-1
CHAPTER 2
MAGNET SYSTEM DESIGN,
INSTALLATION, AND OPERATION
2.0 GENERAL
This chapter provides the user insight into the design, installation, and operation of a typical electromagnet. For
information on how to install the Model 642 please refer to Chapter 3. For Model 642 operation information, refer to
Chapter 4.
2.1 INTRODUCTION
A magnet used with the Model 642 Power Supply is typically an iron pole, twin coil, 4-inch pole diameter, variable air
gap, water cooled electromagnet. Larger magnets can be used depending on their electrical parameters and the magnetic
field requirements. The electromagnet provides a uniform magnetic field in the air gap between two adjustable poles.
The samples, which are to be tested for their magnetic properties, are placed in the air gap with appropriate monitoring
equipment attached. By varying the polarity and intensity of the field, useful data can be collected. A typical
electromagnet is shown in Figure 2-1.
Figure 2-1. A Typical Electromagnet
- Model 642 1
- TABLE OF CONTENTS 5
- LIST OF ILLUSTRATIONS 9
- LIST OF TABLES 10
- CHAPTER 1 11
- INTRODUCTION 11
- 1-2 Introduction 12
- Introduction 1-3 13
- Description (Continued) 13
- 1.2 SPECIFICATIONS 13
- 1-4 Introduction 14
- Specifications (Continued) 14
- Introduction 1-5 15
- 1-6 Introduction 16
- Introduction 1-7 17
- 1.3 SAFETY SUMMARY 17
- 1-8 Introduction 18
- Safety Summary (Continued) 18
- Introduction 1-9 19
- 1.4 SAFETY SYMBOLS 19
- 1-10 Introduction 20
- CHAPTER 2 21
- MAGNET SYSTEM DESIGN 21
- INSTALLATION, AND OPERATION 21
- Magnet System Design 2-3 23
- 2-6 Magnet System Design 26
- Magnet System Design 2-7 27
- 2-8 Magnet System Design 28
- CHAPTER 3 29
- INSTALLATION 29
- 3-2 Installation 30
- 3.2 REAR PANEL DEFINITION 30
- TERMINAL SCREW 32
- WIRE FERRULE 32
- VOLTAGE SELECTOR CARD 32
- VOLTAGE INDICATOR KEY 32
- 3-6 Installation 34
- 3.3.6 Wiring Cover 34
- NO SWITCHES EMERGENCY STOP 35
- REMOTE ENABLE 35
- ALARM CONTACTS 35
- TO REMOTE ALARM CIRCUIT 35
- VALVE AND SWITCH 36
- SOLENOID VALVE 37
- WITH MOUNTING BRACKET 37
- ADJUSTABLE HOSE CLAMP 37
- REINFORCED HOSE 37
- 230 mm (9 in) LONG 37
- LUG COVER 38
- 3-12 Installation 40
- 3.12 DETACHABLE HANDLES 40
- 3.13 RACK MOUNTING 40
- CHAPTER 4 41
- OPERATION 41
- +70.0000 A +35.000 V 42
- Operation 4-3 43
- 4.4 KEYPAD DEFINITION 43
- 4-4 Operation 44
- 4.5 DISPLAY SETUP 44
- 4.6 SETTING OUTPUT CURRENT 44
- Operation 4-5 45
- 4.7 CURRENT RAMP RATE 45
- 4.8 RAMP SEGMENTS 45
- 4-6 Operation 46
- Ramp Segments (Continued) 46
- 4.9 PAUSE RAMP 46
- 4.10 ZERO OUTPUT 46
- Operation 4-7 47
- 4.11 MAXIMUM SETTING LIMITS 47
- 4-8 Operation 48
- 4.12 MAGNET WATER 48
- 4.13 INTERNAL WATER 48
- 4.14 ERROR STATUS DISPLAY 48
- Operation 4-9 49
- 4.16 LOCKING THE KEYPAD 49
- 4-10 Operation 50
- 4.17 COMPUTER INTERFACE 50
- CHAPTER 5 53
- COMPUTER INTERFACE OPERATION 53
- 5.1.2 Remote/Local Operation 54
- Message Strings (Continued) 56
- 5.1.4 Status System 56
- 5.1.4.1 Overview 56
- Register Method Example 59
- *ESE, *ESE? 60
- ERSTE, ERSTE? 62
- *SRE, *SRE? 64
- IBCONF.EXE.eps 71
- 5.1.5.3 Program Operation 72
- 5.1.6 Troubleshooting 72
- 5.2.1 Changing Baud Rate 73
- 5.2.2 Physical Connection 73
- 5.2.6 Message Flow Control 75
- 5.2.7.2 Program Operation 79
- 5.2.8 Troubleshooting 79
- 5.3 COMMAND SUMMARY 80
- CHAPTER 6 91
- OPTIONS AND ACCESSORIES 91
- 6-2 Options and Accessories 92
- CHAPTER 7 93
- SERVICE 93
- 7-2 Service 94
- 7.3 LINE VOLTAGE SELECTION 94
- 7-4 Service 96
- Figure 7-3. Circuit Breaker 96
- Service 7-5 97
- 7.6 ERROR MESSAGES 97
- 7-6 Service 98
- Table 7-3. Operational Errors 98
- 7.7 ELECTROSTATIC DISCHARGE 98
- 7-8 Service 100
- DIGITAL BOARD 101
- LOCATOR PINS 102
- MOUNTING SCREWS 102
- 7-12 Service 104
- 7.10.3 Auxiliary Connector 104
- Pin Name 104
- 7-14 Service 106
- Service 7-15 107
- Pin Symbol Description 107
- 7-16 Service 108
- 7.11 CALIBRATION 108
- 7.11.1 Calibration Interface 108
- 7-18 Service 110
- Service 7-19 111
- 7-20 Service 112
- Service 7-21 113
- 7-22 Service 114
- APPENDIX A 115
- GLOSSARY OF TERMINOLOGY 115
- – 1855) a German 117
- Factor Prefix Symbol 119
- APPENDIX B 121
© 2020, manymanuals.fr. Tous droits réservés | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels